Orion 3000 Manuel d'utilisateur

Orion 3000 Wireless LAN Cable Modem User’s Guide Rev. 1.2a Firmware revision: 5.8.2004 April 14th, 2003

User’s Guide 10 3. You will see the following Welcome screen. 4. Click “Next>”. You will see the following Start screen.

User’s Guide 11 5. Click “Next>”. You will see the following ‘Complete’ screen. 6. Click “Finish”. You will see below screen, a

User’s Guide 12USB cable to the PC by following next section instructions. Installing the Hardware This section explains how to co

User’s Guide 13 2. Insert the CD into the PC’s CD-ROM and click Next. You will see the following screen. 3. Select Search for t

User’s Guide 14 4. Check the CD-ROM drive check box and verify that the CD is in the CD-ROM drive. Click Next to have Windows sear

User’s Guide 15correct location of the driver files. DO NOT proceed if USB Composite Device is displayed in the above window. Conta

User’s Guide 16 8. After files copying is done, you will see the following screen: 9. Click Finish to complete the installatio

User’s Guide 17 10. Choose Yes to restart your computer. 11. After the computer is rebooted, verify that the USB LED is lit on th

User’s Guide 18 3. Select Automatic search for a better driver (Recommended) and click Next. The computer automatically copies the

User’s Guide 19 5. Click Finish after the computer has copied the necessary files. You will see the following screen. 6. Cl

User’s Guide 2Contents 1. BEFORE YOU BEGIN ...

User’s Guide 20 Installing the Software Drivers in Windows 2000 Operating System To install the cable modem software drivers using t

User’s Guide 21 4. Select Search for a suitable driver for my device (recommended. Then select Next. You will see the following s

User’s Guide 22 5. Check the CD-ROM drive check box and verify that the CD is in the CD-ROM drive. Click Next to have Windows locat

User’s Guide 23 7. Click Finish to complete the installation. 8. After the installation is completed, verify that the USB LED is

User’s Guide 24 2. Choose the software automatically (Recommended). Click Next to continue. You will see the following screen.

User’s Guide 25 3. Click Finish to complete the installation. Troubleshooting the USB Installation None of the LEDs are on when

User’s Guide 26 4. Select USB Composite Device and click Remove 5. Click Refresh The Add New Hardware Wizard window appears, displa

User’s Guide 27modem. • Power cycle the cable modem by removing the power adapter from the electrical outlet and plugging it back in

User’s Guide 28configuring TCP/IP. After installed the hardware, your computer can connect the wireless cable modem directly by using

User’s Guide 29X over the NIC in the Network Adapters field. If you see either one, you may have an IRQ conflict. Refer to the manu

User’s Guide 37. TELNET COMMANDS...

User’s Guide 30 • PWR: Indicates that the wireless cable modem has successfully completed internal power-on tests. • USB: Indicate

User’s Guide 31 1. ENET Port: This is where you plug the included Ethernet cable. The other end connects to the Ethernet Jack on t

User’s Guide 32MIBs Support RFC1213, RFC2011, RFC2012, RFC2013,RFC2669, RFC2670, RFC2233, RFC1907, RFC1493, draft-ietf-ipcdn-mcns-bp

User’s Guide 33 7. Telnet commands The Cable Router telnet Login and Password: Login: Password: ** Note: Default Wireless

User’s Guide 34To list keywords or arguments, enter a question mark (?) in place of a keyword or argument. Include a space before the

User’s Guide 35Debug ¾ debug Display corresponding message, the protocol debug just show packet information send to or receive from

User’s Guide 36Download the specified firmware image name from TFTP server and store in as “image 1” or “image 2”. If {1|2} is not sp

User’s Guide 37Change the password of accessing Telnet command. Example: CM>pwd admin Old password: New password: Reconfirm: Chang

User’s Guide 38¾ show version Display hardware and software reversion and board ID. Example: CM>show version Hardware revision:

User’s Guide 39 IP address 30.0.0.9 subnet-mask 255.255.255.248 Link status: link Mode: 10Mbps, half-duplex

User’s Guide 4Security WEP ...

User’s Guide 40Interface USB USB-Host MAC address: 0002.8A0E.ECCA Speed: 12Mbps Link status: disconnect ¾ s

User’s Guide 41 Upstream Symbol Rate : 2560 ksym/sec Upstream Frequency : 28688000 Hz Upstream Mini-Slot Size

User’s Guide 42Web access control CPE interface web access enable. Cable interface web access enable. Access List is

User’s Guide 43 FEC Codeword 16 34 34 75 220 Scrambler Seed

User’s Guide 44CM>show user Index User Name From Alive(sec) Idle(sec) 1 admin

User’s Guide 45Enable/disable dhcp server ¾ dhcp lease-time { 30-2147483647 seconds} Set dhcp server ip lease time ¾ dhcp dns add

User’s Guide 46Example: CM>dhcp reserve-mac add 192.168.100.4 0002.8A25.251D CM>show dhcp TFTP Server IP address : 172.19.89.19

User’s Guide 47 ¾ interface ethernet mac-address {mac address} Assign mac-address for ethernet interface CM>interface ethernet

User’s Guide 48Example: CM>interface wireless ssid Ambit Set SSID to Ambit ¾ interface wireless host {host name} Set Wireless LA

User’s Guide 49¾ ip nat {enable/disable} Enable/disable NAT/PAT gateway function ¾ nat timer {tcp/udp/gre/icmp} {1~86400 sec} Set

User’s Guide 5 1. Before You Begin Your new wireless cable modem provides high-speed wireless access to the Internet by using IEEE 80

User’s Guide 50Set NAT/PAT Port forwarding table CM>nat static portmapping add 21 192.168.100.23 ftp CM>show nat config NAT :

User’s Guide 51Example: CM>nat static ip enable Static IP will be enabled after "reset" command. ¾ nat static ip {ipad

User’s Guide 52Wireless LAN Cable Router IP address. The standard MAC access list performs frame filtering based on source MAC addres

User’s Guide 53Download the Wireless Cable Router configuration from remote tftp server. The configuration file must be text file. ¾

User’s Guide 54 8. Web User Interface Accessing the Web User Interface 1. The PC connected to the wireless cable modem must support

User’s Guide 55Cable Modem Status

User’s Guide 56Downstream Upstream

User’s Guide 57Upstream Burst Operation Parameters

User’s Guide 58Event Log

User’s Guide 59Wireless Configuration SSID • You can input SSID to group your wireless network. The wireless clients that have the

User’s Guide 6 Contact Your Local Cable Operator Before installing you new wireless cable modem, you must contact your local cable se

User’s Guide 60WEP Key • 64 bits WEP requires a 10 Hexadecimal digits key, and 128 bits WEP key needs a 26 Hexadecimal digits key. A

User’s Guide 7¾ Wireless client drivers ¾ Wireless LAN Utility ¾ This user guide Not Supplied Verify that these items are availa

User’s Guide 8 Chapter 2 provides instructions for installing your wireless cable modem using the Wireless feature. Chapter 3 provid

User’s Guide 9example, a wall that is 1 foot thick, at a 45-degree angle appears to be almost 2 feet thick. • Make sure PC's w